Ultra High Pressure Spiral Hydraulic Hose

WATERBLAST HOSE PRODUCER: WATERJET CLEANING PIPE ITALY REPLACEMENT

producers, hoses couplings Ireland manufacturers by rubber pressure washer hose coupling quick release India suppliers in Abu Dhabi Ajman Dubai Fujairah Ras-al-Khaimah Sharjah UAE- Gulf, multi-spiral rubber hoses, high-pressure hydraulic fluid hose fitting and dewatering system water pipe discharge importers of United Arab Emirates buy from India exporter, HIC International Co.

multi-spiral-ultra-high-pressure-hoses

multi-spiral-ultra-high-pressure-hoses

water-blast-hose-and-fittings

water-blast-hose-and-fittings

hydraulic-wire-braided-hose

optional-hydraulic-wire-braided-hose

optional-hydraulic-wire-braided-hose

4SH Six Wire Braided Spirals Ultra High-Pressure Hydraulic Hose

Part Nubmer I.D. O.D MaximumWorkingPressure MinimumBurstPressure MinimumBendRadius Weight(lbs/ft)
PSI BAR PSI BAR
12‐4SH 3/4” 1.260” 6000 420 24,000 1680 11.0” 1.01
16‐4SH 1" 1.535" 5500 380 22,000 1520 13.5” 1.34
20‐4SH 1¼” 1.772” 5000 325 20,000 1300 18.0” 1.61
24‐4SH 1½" 2.087" 4200 290 17,600 1160 22.0” 2.06
32‐4SH 2" 2.677” 3600 250 14,400 1000 27.0” 3.05

Waterblast 4 Spiral Ultra High-Pressure Rubber Hose: HIC Universal

I.D.: O.D [mm] Working pressure [bar] Bursting pressure [bar] Bending radius [mm] Weight [kg/m]
[inch]: [mm]
1/4 6.4 17.6 1250 3125 200 0.61
3/8 9.5 21.4 1250 3125 210 0.88
1/2 12.7 24.6 1100 2750 230 1.22
3/4 19 32 1100 2750 250 1.83

Water Blasting 6 Spirals Ultra High-Pressure Jetting Hose Pipe

I.D.: O.D [mm] Working pressure [bar] Bursting pressure [bar] Bending radius [mm] Weight [kg/m]
[inch]: [mm]
1/2 12.7 27.8 1450 3625 250 1.82

4SP Four Steel Wire Spiral Supreme Pressure Rubber Hose

Part Nubmer I.D. O.D MaximumWorkingPressure MinimumBurstPressure MinimumBendRadius Weight(lbs/ft)
PSI BAR PSI BAR
6‐4SP 3/8” .827” 6500 450 26,000 1800 7.0” .47
8‐4SP 1/2” .984” 6000 415 24,000 1660 9.0” .62
10‐4SP 5/8” 1.102” 5000 350 20,000 1400 10.0” 1.61
12‐4SP 3/4” 1.260” 5000 350 20,000 1400 11.8” .97
16‐4SP 1" 1.555” 4000 275 16,000 1100 13.3” 1.26

R13 Multi Spiral Hydraulic High Pressure Rubber Hose

Part Nubmer I.D. O.D MaximumWorkingPressure MinimumBurstPressure MinimumBendRadius Weight(lbs/ft)
PSI BAR PSI BAR
12‐R13 3/4” 1.256" 5000 345 20,000 1380 9.5” .99
16‐R13 1” 1.516” 5000 345 20,000 1380 12.0” 1.33
20‐R13 1¼” 1.953” 5000 345 20,000 1380 16.5” 2.51
24‐R13 1½” 2.248” 5000 345 20,000 1380 20.0” 3.16
32‐R13 2" 2.791” 5000 345 20,000 1380 25.0” 4.51

Also producing R15, R16, R17 and Isobaric Large Bore hose till 3 Inch Diameter with a working pressure of 350 bar, safety factor 4:1 for underground mining application


R2 Two Steel Wire Braids Reinforced Hydraulic Rubber Hose

Part Nubmer I.D. O.D MaximumWorkingPressure MinimumBurstPressure MinimumBendRadius Weight(lbs/ft)
PSI BAR PSI BAR
4‐2SN 1/4” .591” 5800 400 23,200 1600 2.0” .25
6‐2SN 3/8” .748” 4800 330 19,200 1320 2.5” .35
8‐2SN 1/2” .878” 4000 280 16,000 1120 3.5” .41
10‐2SN 5/8” 1.004” 3600 250 14,400 1000 4.0” .50
12‐2SN 3/4” 1.157” 3100 215 12,400 860 4.75” .62
16‐2SN 1” 1.500” 2400 165 9600 660 6.0” .91
20‐2SN 1¼” 1.854” 1800 125 7200 500 16.5” 1.37
24‐2SN 1½” 2.146” 1300 90 5200 360 20.0” 1.50
32‐2SN 2” 2.646” 1150 80 4640 320 25.0” 1.92

R1 One Steel Wire Braided Reinforced Fluid Pressure Rubber Hose

Part Nubmer I.D. O.D MaximumWorkingPressure MinimumBurstPressure MinimumBendRadius Weight(lbs/ft)
PSI BAR PSI BAR
4‐1SN 1/4” .528” 3265 225 14,500 900 2.0” .15
6‐1SN 3/8” .685” 2610 180 10,440 720 2.5” .22
8‐1SN 1/2” .815” 2320 160 9280 640 3.5” .27
10‐1SN 5/8” .941” 1890 130 7560 520 4.0” .33
12‐1SN 3/4” 1.094” 1525 105 6100 420 4.75” .42
16‐1SN 1” 1.449” 1275 88 5100 352 6.0” .61
20‐1SN 1¼” 1.764” 915 63 3660 252 16.5” .91
24‐1SN 1½” 2.008” 725 50 2900 200 20.0” 1.00
32‐1SN 2” 2.539” 580 40 2320 160 25.0” 1.50

RIGHT INSTALLATION OF HYDRAULIC FLUID HOSE END FITTINGS GUIDE

Satisfactory performance and appearance depend upon proper hose installation. Excessive length destroys the trim appearance of an installation and adds unnecessarily to the cost of the equipment. Hose assemblies of insufficient length to permit adequate flexing, expansion or contraction will cause poor power transmission and shorten the life of the hose. The diagrams below offer suggestions for proper hose installations to obtain the maximum in performance and economy.

Since hose may change in length from +2% to -4% under the surge of high pressure, provide sufficient slack for expansion and contraction.

Avoid sharp twist or bend in hose by using proper angle adapters.

Where the radius falls below the required minimum, an angle adapter should be used as shown above to avoid sharp bends in hose.

Obtain direct routing of hose through use of 45° and 90° adapters and fittings. Improve appearance by avoiding excessive hose length.

Due to changes in length when hose is pressurised, do not clamp at bends so curves absorb changes and protect the hose with a spring guard. Do not clamp high and low pressure lines together and protect the hose with a spring guard.

Adequate hose length is most important to distribute movement on flexing applications and to avoid abrasion.

To avoid twisting in hose lines bent in two planes, clamp hose at change of plane, as shown.

To prevent twisting and distortion, hose should be bent in the same plane as the motion of the boss to which the hose is connected.

Hose should not be twisted. Hose is weakened when installed in twisted position. Also pressure in twisted hose tends to loosen fitting connections. Design so that machine motion produces bending rather than twisting.

Never use a bending radius less than the minimum shown in the hose specification tables. Avoid sharp bend in hose to reduce collapsing of line and restriction of flow by using proper spring guard. Exceeding minimum bend radius will greatly reduce hose assembly life.

Warranted quality high pressure hydraulic flow Hydraulic Pneumatic Pressure-proof Laboratory Test Certificate
E-Catalogue HIC Rubber Hose Download

Rubber Hose Types

providers in India, Saudi Arabia, China, Netherlands, UK, Russia, Germany, USA, France, Brazil, South Korea, Japan, Indonesia Jordan, Malaysia, UAE, Oman supplied to other Asian countries

Shipping Time:Generally, within 3-4 weeks or as stipulated in quote and accepted order.